Smart Alarm and Security with Fibaro
Fibaro HC2 and HC lite could be configured to utilise sensors for Smart home security purposes.
To configure Fibaro for Smart home security purposes below configurations should be made:
1- Setting up access controls
2- Setting up alarm panel
3- Setting up sensors
4- Setting up Alarm actions
5- Managing User Interface
Setting up access control
An important aspect of every smart security system is who can arm and disarm it as well as who receives notifications when a breach has happened.
To create a new user co to HC configuration and select “access control” and add a new user.
We call our user “Leon” in this example.
Setting up the alarm panel
For the Fibaro HC to work as a security system we need to set up the alarm panel.
To do this go to “Panels” and select “Alarm panel” and then “Advanced”
Click on “Configure”
Click on “Yes” and then Set a Pin number
The Alarm panel configuration is now complete.
Setting up sensors
Sensors must be configured for the alarm system to work. The configuration would be as following:
1-Delay in Arming or Disarming sensor when system is Armed or Disarmed
2-Status of the sensor before Arming. This setting is used to allow or prevent the system from Arming if the sensor is in safe or unsafe mode.
3-Including the sensor in the Alarm system.
To set the above configuration go to the device (Sensor) and select advanced:
Setting up Alarm Actions
In addition to the above we need to configure the actions which system takes when a breach has happened.
The actions could include but not limited to the following:
2-Running specific scenarios
To configure a notification go to “Panels” and select “Notification Panel” and create a new notification like below screen shot:
In the next step we are going to create a scene to detect if a breach has happened and trigger the “Alarm_Detected” notification:
Create a Scene and name it “Alarm_Triggered”
Make sure you tick the “Do not allow alarm to stop the scene while alarm is running”, this allows the scene to run even if an alarm has happened.
The Scene triggers “Alarm_Detected” notification if an Alarm Breach is detected:
The value of the Dummy Variable “SecTrig” is Always Zero.
You can also program the Scene to start siren, turn lights on or off etc.
The “Alarm_Triggered” Scene will not run automatically and we need to add it to the alarm Actions by going to the Alarm Panel and select the “Advanced” tab:
You can Activate or Deactivate all of the other Pre-existing actions as well as adding a new action by clicking on “Add Action”.
Add “Alarm_Triggered” scene to the list of Actions and “Activate” it.
Managing User Interface
In this step we setup the user interface.
Basically you can Arm and Disarm each sensor by clicking on individual sensor and select Arm or Disarm.
In most cases we need to Arm/Disarm the entire house or different areas which can include multiple sensors.
One way of Arming and Disarming a group of sensors is to create a dummy room and include all security sensors into that room. In this example we create a room called “Security” and move all security sensors into that room.
Once the room is created you can click on the Alarm icon on mobile app:
Then select the Security room and then Arm the room which Arms all of the sensors in the Security room.
When Disarming the Security Room a Pin pad will be displayed which you need to enter the pic code which you set at the beginning in the alarm panel configuration.
Smartest Home is the leading supplier of the smart home automation and Z-Wave products and solutions across Australia.
- November 2020 (1)
- June 2020 (1)
- May 2020 (1)
- April 2020 (1)
- March 2020 (2)
- January 2020 (2)
- December 2019 (2)
- July 2019 (1)
- June 2019 (1)
- April 2019 (2)
- February 2019 (3)
- January 2019 (2)
- December 2018 (1)
- November 2018 (1)
- October 2018 (1)
- August 2018 (4)
- July 2018 (3)
- June 2018 (1)
- May 2018 (1)
- April 2018 (2)